0
Owner's of the Panasonic Camcorder Memory Card Camera-Recorder gave it a score of 0 out of 5. Here's how the scores stacked up:
– 78 –
Chapter 4 Adjustments and Settings for Recording — Viewnder status display
[SDI OUT2] — Displays the status of the signal output from the <SDI OUT2> terminal.
[OUTPUT]
Displays the status of [MEM]/[CAM] or [OFF] set by [SDI OUT2] and [MONITOR OUT
MODE] in the main menu → [I/F SETUP] → [OUTPUT SEL].
[SELECT]
Displays the signal format set by [SDI2/HDMI OUT] and [1080P SDI2/HDMI OUT] in the
main menu → [I/F SETUP] → [OUTPUT SEL] by [SYSTEM]/[DOWNCON]/[1080i].
[CHAR] Displays the position of the <MON OUT CHARATER> switch by [ON]/[OFF].
[P2CARD STATUS]
—
Displays the status of the P2 card inserted in the card slot, remaining capacity and total
used capacity.
The statuses of cards to be displayed are as follows:
[ACTIVE]/[ACCESSING]/[INFO READING]/[FULL]/[PROTECTED]/[NOT SUPPORTED]/
[FORMAT ERROR]/[AUTH NG]/[REC IMPOSSIBLE]/[NO CARD]
For details, refer to “P2 card access LEDs and status of P2 cards” (page 32).
[TOTAL P2/mP2]
Displays the remaining capacity/total capacity totaled for slots 1/2 (or slots 3/4) and the
recording medium ([P2] or [mP2]).
[SLOT1] or [SLOT3] Displays the status of the P2 card in slot 1 (or slot 3) and remaining capacity/total capacity.
[SLOT2] or [SLOT4] Displays the status of the P2 card in slot 2 (or slot 4) and remaining capacity/total capacity.
[PROXY]
[MEDIA]
Displays the media selection status for proxy recording.
[P2]/[P2&SD]/[OFF]
[MODE]
Displays the setting status for proxy recording mode.
[STD 2CH MP4]/[SHQ 2CH MOV]/[HQ 4CH MOV]/[HQ 2CH MOV]/[LOW 2CH MOV]
[SUPER]
Displays the superimposed setting status of the time code.
[UPPER]/[LOWER]/[OFF]
[PROXY ERROR] Displays the operation error on the proxy module.
[AUDIO] screen
Displays audio settings and the selection status of each recording channel.
[SAMPLE RES] — Displays the number of audio recording bits.
[MIC POWER (MENU)] — Displays the menu setting status of power supply to the microphone.
[FRONT]
Displays the power supply status to the front microphone currently set in the main menu →
[I/F SETUP] → [MIC/AUDIO] → [FRONT MIC POWER] by [ON]/[OFF].
[REAR]
Displays whether to set supply of power to the microphone on the <AUDIO IN> terminal at
the rear in the main menu → [I/F SETUP] → [MIC/AUDIO] → [REAR MIC POWER].
f [OFF]: Power is not supplied to the microphone.
f [ON]: Power is supplied to the microphone when the <LINE>/<MIC> selector switch is set
to <MIC> and the microphone input power selector switch is set to <+48V>.
[VR SELECT]
—
Displays which of [CH1/2] and [CH3/4] the audio level adjustment dial is to be set as
enabled to in the main menu → [I/F SETUP] → [MIC/AUDIO] → [VR SELECT].
[LEVEL]
[CH1/2/3/4]
Displays the recording level adjustment method currently selected on each channel.
f [VR]: Displayed when manual adjustment using the adjustment dial is set.
f [MENU]: Displayed when manual adjustment using [LVL CONTROL CH3(CH1)]/[LVL
CONTROL CH4(CH2)] is set in the main menu → [I/F SETUP] → [MIC/AUDIO].
f [AUTO]: Displayed when automatic adjustment is set.
[F.VR]
[CH1/2/3/4]
Displays by [ON]/[OFF] whether the <F.AUDIO LEVEL> dial is enabled on the channel to
which [VR] (manual adjustment by adjustment dial) is displayed in [LEVEL].
[A.IN]
[CH1/2/3/4]
Displays the input status of each channel by [FRONT] (front)/[REAR] (rear)/[W.L.]
(wireless).
[METER] [CH1/2/3/4] Displays the recording level of each channel.
[CAC INFO] screen
Displays the operation status or information of CAC.
[CAC CONT] Displays the operation status of CAC.
f [ON]: [ON] is set to in the main menu → [MAINTENANCE] → [CAC ADJ] → [CAC CONTROL], and CAC is active.
f [STOP]: [ON] is set to in the main menu → [MAINTENANCE] → [CAC ADJ] → [CAC CONTROL], however, CAC operation
stops under certain data or lens conditions.
f [OFF]: [OFF] is set to in the main menu → [MAINTENANCE] → [CAC ADJ] → [CAC CONTROL], and CAC is not active.
[CAC MODE] Displays the operation mode of CAC.
f [AUTO]: The CAC le is automatically selected.
[CONNECT LENS TYPE] Displays the lens ID of the currently connected digital lens.
[SELECT FILE TITLE] Displays the title and the le version of the CAC le currently used in the operation. The CAC le can be set in the main menu
→ [MAINTENANCE] → [CAC ADJ].
[CAC WARNING] Displays a warning when operation of CAC has stopped.
f [CAC LENS DATA INVALID]: This is displayed, for example, when the response data from the lens is not supported.
f [LENS INIT. NOT COMPLETED]: This is displayed, for example, when initialization of the lens cannot complete.
Find Your Products By Category
Please Login
