0
Owner's of the Panasonic Camcorder Memory Card Camera-Recorder gave it a score of 0 out of 5. Here's how the scores stacked up:
– 197 –
Chapter 9 Maintenance and Inspection — Warning system
Monitor display
Description Camera operation
First row Second row
[REC WARNING] (occurs
during recording)
[PULL DOWN] (occurs
during recording)
[PULL DOWN ERROR]
(occurs at times other
than during recording)
The video pull-down sequence and time code values are not
synchronized. Check the signal.
Continue
[REC WARNING] [REC DATA]
Displayed when an error occurs in recorded data during recording.
Turn the power off and on before using it again.
Continue or Stop
[RUN DOWN CARD]
(slot number)
None
The maximum number of overwrites has been exceeded.
Replacement of the P2 card is recommended.
Continue
[SD CARD] (slot number) None
An SDHC/SDXC memory card is inserted into the microP2 memory
card slot. The current operation will continue. Use of microP2 or P2
memory card is recommended.
Continue
[SLOT1/2 CANNOT
REC] or [SLOT3/4
CANNOT REC]
[microP2 SELECTED] or
[P2 SELECTED]
Displayed when the card is inserted into the slot which is not selected
as the recording slot.
Stop
[TEMPORARY PAUSE] [IRREGULAR SIG]
Correct recording is not possible due to disruption of input signals
of the <GENLOCK IN> or <SDI IN> terminal, and recording is
suspended temporarily. The clip will be divided. Recording resumes
when the signal returns to normal. However, during loop recording,
recording does not resume.
Suspend → Resume
[WIRELESS-RF] None Audio wireless reception status is poor. Continue
Warning/error displays in the thumbnail operation, menu operation, and USB storage mode
r Thumbnail and menu
Message Description Measure
[AUTHENTICATION ERROR!] Manual authentication failed. Enter the correct password.
[CANNOT ACCESS!]
Data cannot be accessed due to a content defect or some
other reason.
Ensure the health of the media and the clips.
[CANNOT CHANGE!]
For a clip with the [
] mark, where a thumbnail cannot be
generated, the thumbnail cannot be modied in the text memo
position.
Correct the settings and content to enable display of the
thumbnail.
[CANNOT DELETE!] The content versions do not match. Cannot delete. Match the device and contents version.
[CANNOT FORMAT!] A P2 card problem or some other reason prevents formatting. Check the P2 card.
[CANNOT RE-CONNECT!]
Clips cannot be remerged because either clips not recorded
across multiple P2 cards are selected or other reasons.
Check the selected content.
[CANNOT REPAIR IN
SELECTION!]
Some of the selected clips cannot be repaired. Check the selected content.
[CANNOT REPAIR!] Content that cannot be repaired is selected. Check the selected content.
[CANNOT SAVE! FILE NAME
IN USE]
A settings le of the same name exists on the SD memory
card.
Use another name to save the le.
[CARD FULL!] The P2 card or SD memory card is full. Insert a card with free space available.
[COPY IMPOSSIBLE. TOO
LARGE CLIP CONTAINED!
(CLIP NAME: XXXXXX)]
Files exceeding 4 GB cannot be copied to memory card of
32 GB or less.
Copy to microP2 cards with capacity of 64 GB or more.
[INVALID VALUE!] The data value you entered is invalid. Enter data within the normal range.
[LACK OF CAPACITY!] There is not enough recording capacity left on the card. Insert a card with sufcient recording capacity.
[MISSING CLIP!]
Shot marks cannot be attached to the clips unless all clips
recorded over multiple P2 cards are present.
Insert all P2 cards over which recording extended.
[NO CARD!] No P2 or SD memory card is inserted. Insert the relevant media.
[NO COPY TO SAME CARD!] A clip cannot be copied to the card storing the original clip.
Copy the selected clip to a card that does not contain the
original clip.
[NO FILE!] The specied le does not exist. Check the le.
[NO INPUT!] No data is entered. Enter data and then set.
[NO SD CARD!] No SD memory card. Insert an SD memory card.
[NOT SELECTED!] Attempted to delete without selecting clips. Select clips to delete.
[SAME CLIP IS SELECTED!]
Multiple instances of the same clip (copies) are included in the
clips selected.
Multiple instances of the same clip (copies) cannot be copied
simultaneously. Remove instances of the same clip from
selected items.
[TOO MANY CLIPS!] Too many clips are selected. Reduce the number of selected clips.
[UNKNOWN CONTENTS
FORMAT!]
This is a warning of the contents for the version that is not
supported by the camera.
Match the device and content versions.
[UNKNOWN DATA!]
The metadata character code is invalid.
The metadata character code is UTF-8. Enter valid characters
using a viewer.
There is a problem with data in the le. Create the le again.
Find Your Products By Category
Please Login
