0
Owner's of the Panasonic Camcorder Memory Card Camera-Recorder gave it a score of 0 out of 5. Here's how the scores stacked up:
– 196 –
Chapter 9 Maintenance and Inspection — Warning system
Warning content
There is an error in the fan and it stops. Otherwise [OPTION MENU] → [OPTION] → [FAN MODE] → [OFF] has been
set.
Recording or playback operation
Operation will continue, but if the camera is operated with the fan stopped, the temperature rises and recording/playback
may not operate normally.
Action to take
If the fan has stopped with error, stop using immediately and consult your dealer.
If the fan has stopped, temperature of the camera will rise. Therefore, do not use the camera for a long period of time.
Use the tripod, etc., and do not touch the camera directly.
Error code
If errors occur on the camera for any cause, the following error code is displayed on the time code display in the display window. Check the types of
warning, and deal with the error according to “Warnings description list” (page 194).
Code No.
Message display
Description Type of warning
First row Second row
[E-30] [TURN POWER OFF] [P2 CARD] P2 card removal error
3 Card removal error
[E-31] [TURN POWER OFF] [SYSTEM MODE] System mode error
2 Mismatched format
[E-33] [SYSTEM ERROR] [CAMERA] Camera unit error
1 System error
[E-34] [SYSTEM ERROR] [LCD MICON] LCD microcomputer error
1 System error
[E-35] [SYSTEM ERROR] [CODEC] Codec control error
1 System error
[E-36] [SYSTEM ERROR] [P2 SYSTEM] P2 system error
1 System error
[E-37] [SYSTEM ERROR] [P2CS] P2CS microcomputer error
1 System error
[E-39] [SYSTEM ERROR] [INITIALIZE] Video initialization error
1 System error
[E-63] No display No display System control microcomputer error
1 System error
[E-64]
[SYSTEM ERROR]
or no display
[FRAME SIGNAL]
or no display
Standard signal error
1 System error
Warning information display
Monitor display
Description Camera operation
First row Second row
[AUTH NG CARD] (slot
number)
None
CPS authentication of microP2 memory card has failed. The microP2
memory card with CPS authentication failed cannot be recorded or
played back. Select [AUTHENTICATE] in the main menu → [CLIP],
and enter the password.
Continue
[BACKUP BATT EMPTY] None
Displays any reduced voltage detected on the backup battery in the
internal clock when the power is turned on.
Follow “Charging the built-in battery” (page 193) to charge the
battery.
Continue
[CARD ERROR] (slot
number)
None
Displayed when an data error caused by the P2 card occurs during
recording.
Displayed after recording stops until the next operation. Also
displayed for three seconds during playback when a P2 card error
causes playback to stop.
Replace the P2 card of the slot where the error occurred.
Stop
[DIR NG CARD] (slot
number)
None
The directory position is not correct. Make a card backup immediately
and use again after formatting.
Continue
[FAN STOPPED] None
Displayed when the fan motor stops.
The camera operates even if the fan stops. Refrain from using
immediately.
Continue
[PB INTERMITTENT]
(slot number)
None
Playback is interrupted on the SDHC/SDXC memory card. A card
whose playback performance cannot be assured is inserted. Use of
microP2 or P2 memory card is recommended.
Continue
[PROXY ERROR] None
Proxy error
For details, refer to “Error displays about proxy data recordings”
(page 43).
Continue
[PROXY REC
WARNING]
None
Proxy error
For details, refer to “Error displays about proxy data recordings”
(page 43).
Continue
[REC IMPOSSIBLE] (slot
number)
None
An SDHC/SDXC memory card is inserted into the microP2 memory
card slot.
Recording to the SDHC/SDXC memory card is disabled. Record to
microP2 or P2 memory cards.
Continue
[REC WARNING] [FRAME SIGNAL]
Displayed when a video or audio error occurs during recording. Turn
the power off and on before using it again.
When input signals are disrupted, recording continues while disrupted
images are recorded. Check the signal to be input to the camera.
Continue
[REC WARNING] [OVER MAX# CLIPS]
Displayed when attempting to record in excess of the maximum total
number of clips allowed for one P2 card.
Replace the P2 card or delete unnecessary clips.
Stop
Find Your Products By Category
Please Login
