0
Owner's of the Panasonic Camcorder Memory Card Camera-Recorder gave it a score of 0 out of 5. Here's how the scores stacked up:
– 186 –
Chapter 8 Connecting to External Devices — Connection function via <USB2.0> or <USB3.0> terminals
t Download the USB driver from the website and install it into your computer. For installation procedure of the driver, refer to the installation manual on
the website.
For the latest information on the driver, visit the following website.
http://pro-av.panasonic.net/
t The camera supports only USB 2.0. Ensure your computer supports USB 2.0.
t When connecting the camera to a computer via USB, ensure that no other device is connected to the computer via USB.
t When connecting the camera via USB, do not eject the P2 card.
t When USB is connected, the P2 card access LED turns off when not accessed.
t When the camera is operating in the USB device mode, no camera shooting, recording/playback operation or clip thumbnail operation is allowed.
t When the camera is operating in the USB device mode, the P2 card remaining capacity and status are not displayed. Video and audio are not output
to the viewnder, LCD monitor and <SDI OUT1> terminal or monitor output terminals (<SDI OUT2>, <HDMI OUT>, and <VIDEO OUT>).
USB storage mode
A hard disk drive or solid-state drive connectable to the <USB3.0> terminal (host) via USB 2.0 or USB 3.0 can be connected to store card data, view
thumbnails of saved clips, or write back to a P2 card.
Switching to the USB storage mode
Fig. 1 Fig. 2
1
Set [STORAGE] in the main menu → [I/F SETUP] → [USB/LAN] → [USB MODE SELECT]. (Fig. 1)
For details, refer to “Setting menu basic operations” (page 134).
2
Set [ON] in the main menu → [I/F SETUP] → [USB/LAN] → [USB MODE]. (Fig. 2)
fThe camera enters the USB storage mode.
fDuring USB storage mode, [USB STORAGE CONNECTED] is displayed at the center of the viewnder screen and the <USB> lamp is illuminated.
If the hard disk drive is not connected properly, [USB STORAGE DISCONNECTED] is displayed and the <USB> lamp ashes.
f[USB MODE] can be assigned to the <USER> buttons (<USER MAIN>/<USER1>/<USER2>), the <SHOT MARKER>, and <TEXT MEMO>
buttons in the main menu → [CAMERA] → [USER SW]; pressing these buttons switches between USB storage mode and normal storage mode.
However, if these buttons are pressed while a menu or thumbnail is open, the mode cannot be changed to USB device mode or normal mode.
For details, refer to “Assigning functions to <USER> buttons” (page 56).
3
Press the <THUMBNAIL> button.
fThe thumbnail screen is displayed.
fEnsure that [USB] is displayed at the top right of the screen.
fIf a storage device is connected, the icon that indicates storage device status at the top right illuminates. However, a red mark indicates that the
device cannot be used.
For USB storage mode details, refer to “Connecting to external devices using the <USB3.0> terminal (host) (USB storage mode)” (page 123).
4
Exit the USB storage mode.
There are three ways to do so:
fTurn the <POWER> switch of the camera to <OFF>.
fWith the thumbnail screen closed, set the main menu → [I/F SETUP] → [USB/LAN] → [USB MODE] to [OFF].
fPress any one of the <USER> buttons (<USER MAIN>/<USER1>/<USER2>), <SHOT MARKER> button, or <TEXT MEMO> button to which [USB
MODE] is assigned. However, this is disabled when a menu or thumbnail is open.
@@
NOTE
t In USB storage mode, a P2 card can be played back. Camera video and external input cannot be recorded.
The clips written to the hard disk drive must be written back to the P2 card for playback.
t A storage device cannot be connected to the <USB2.0> terminal (sub-host) (page 23).
t While connecting a storage device, use the fully charged battery or an external DC power supply to avoid problems in copying or formatting
operations.
t For details on storage devices, refer to “Storage device types and available functions” (page 123).
Find Your Products By Category
Please Login
