Panasonic Camcorder Memory Card Camera-Recorder User Manual

0

Out of 0 Ratings

Owner's of the Panasonic Camcorder Memory Card Camera-Recorder gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 209
 
– 74 –
Chapter 4 Adjustments and Settings for Recording — Viewnder status display
[TEMPORARY PAUSE
IRREGULAR SIG]
Displayed when the reference signal is disrupted and recording is suspended during generator lock input, etc.
[EOM] Displayed when there is no space remaining on the P2 card.
[BOS] Displayed when the playback position is at the beginning of all clips.
[EOS] Displayed when the playback position is at the end of all clips.
[CANNOT REC]
Displayed when recording to the P2 card is not possible, for example, immediately after power is turned on or the P2 card is
inserted. Detailed information of the P2 card can be checked in the mode check [FUNCTION] screen. For details, refer to “Mode
check display” (page 77).
[CANNOT PLAY] Displayed when playback is not possible, for example, when there are no clips on the P2 card or the P2 card is not inserted.
[TEXT MEMO] Displayed when a text memo is recorded.
[TEXT MEMO INVALID] Displayed when a text memo could not be recorded.
[MARK ON/OFF] Displayed when shot marks are added or deleted. For details on shot marks, refer to “Shot mark recording function” (page 39).
[SHOT MARK INVALID] Displayed when shot marks cannot be added.
[UPDATING] Displayed when playback operation is not accepted during updating of the clip information for playback.
[USB DEVICE]
Displayed when the USB device mode is set. Flashes during migration through modes, and after migration through modes
is completed, [CONNECTED] is displayed when communication is possible and [DISCONNECTED] is displayed when
communication is not possible.
[USB STORAGE]
Displayed when the USB storage mode is set. Flashes during migration through modes, and from then on, [CONNECTED]
is displayed when the external hard disk is recognized successfully and [DISCONNECTED] is displayed when it cannot be
recognized.
[THUMBNAIL OPEN] Displayed during thumbnail operation.
[TC REGEN] Displayed when the <RET> button on the lens is pressed to regenerate to the time code of the last recorded clip to the P2 card.
[SLOT SELECT]
Flashes when the <USER> button assigned with [SLOT SEL] is pressed and while switching processing of the recording slot on
the P2 card is being executed.
[SLOT SELECT
INVALID]
Displayed when the <USER> button assigned with [SLOT SEL] is pressed and switching processing of the recording slot on the
P2 card is not possible.
For details on warnings, refer to “Warning information display” (page 196).
17 Time code display
[TCG 12:59:59:20] Displays the time code generator value.
[TCR 12:59:59:20] Displays the timecode reader value.
[VUBG AB CD EF 00]
([UBG AB CD EF 00])
Displays the user’s bit generator value.
[VUBR 12 34 56 78]
([UBR 12 34 56 78])
Indicates the user’s bit reader value.
[CTL −1:59:59:20]
Displays the CTL counter value.
18 Audio input line and level meter display
[----r----+]
Displays the selected channel and its audio level.
[F] Displayed when the <AUDIO IN> switch is <FRONT>.
[W] Displayed when the <AUDIO IN> switch is <W.L.>.
[R] Displayed when the <AUDIO IN> switch is <REAR>.
19 Iris override display
Displays the compensation level when the iris overwrite is functioning.
[++]
Aperture opens by about 1.
[+]
Aperture opens by about 0.5.
[−−]
Aperture closes by about 1.
[−]
Aperture closes by about 0.5.
(No display) Reference state.
20 Super iris display
Displayed when super iris is active.
21 Iris, F value
[NC] Displayed when the lens cable is not connected.
[OPEN] Displayed when the lens aperture is open.
[F1.7] to [F16] Displays the lens aperture value.
[CLOSE] Displayed when the lens aperture is closed.
fDisplayed when a lens with an aperture value display function is used. Also, ashes when the iris override is variable.
22 Super black display
Displayed when super black is active.
23 Zoom display
[Z00] to [Z99]
Displays the zoom amount. Note, however, that this item is not displayed in the case of lenses without a zoom position return
even if it is set to be displayed.
[Z**.*mm]
When a serial lens is connected, the display unit can be changed in the main menu → [VF] → [VF INDICATOR] → [ZOOM/
FOCUS].

   Find Your Products By Category