Kramer Electronics TV Cables Kramer Electronics TV Cables User Manual

0

Out of 0 Ratings

Owner's of the Kramer Electronics TV Cables Kramer Electronics TV Cables gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 56
 
Your VP-4x8AK 4x8 VGA / UXGA / Audio Matrix Switcher
9
9
Table 3: Rear Panel VP-4x8AK 4x8 VGA / UXGA / Audio Matrix Switcher Features
#
Feature
Function
1 AUDIO INPUT 3.5mm Mini
Connectors
Connect to the unbalanced stereo audio acceptors (from 1 to 4)
2 AUDIO OUTPUT Terminal Block
Connectors
Connect to balanced stereo audio sources (from 1 to 8)
3 Power Switch Switch for turning the unit ON or OFF
4 INPUT XGA 15-pin HD Connectors Connect to the video sources (from 1 to 4)
5 LOOP XGA 15-pin HD Connectors Connect looped input to output acceptor (1 to 4)
6 OUTPUT XGA 15-pin HD Connectors Connect to the output acceptors (from 1 to 8)
7 PROG Button Push in for “Program” to upgrade to the latest Kramer firmware
via RS-232 (see Section
8), or release for “Normal” (the factory
default)
8 RS-485 TERM DIP-switch Use for RS-485 Termination
1
9
: ON for RS-485 Line Termination
with 120Ω; OFF for no RS-485 Line Termination
RS-232 9-pin D-sub Port Connects to the PC or the remote controller
10 REMOTE IR Opening
2
Connects to an external IR receiver unit for controlling the
machine via an IR remote controller instead of using the front
panel IR receiver
3
11
FACTORY RESET Button Press to reset to factory default definitions
4
:
IP Address: 192.168.1.39
Mask: 255.255.255.0
Gateway: 192.168.1.1
12 ETHERNET Connector Connects to the PC or other serial controller through computer
networking
13 RS-485 Terminal Block Port Pins B (-) and A (+) are for RS-485; Pin G (Ground) may be
connected to the shield of the cable if desired
14 Power Connector with Fuse AC connector enabling power supply to the unit
4.1 Using the IR Transmitter
You can use the RC-IR3 IR transmitter to control the machine via the built-in IR
receiver on the front panel or, instead, via an optional external IR receiver
5
. The
external IR receiver can be located up to 15 meters away from the machine. This
distance can be extended to up to 60 meters when used with three extension cables
6
Before using the external IR receiver, be sure to arrange for your Kramer
dealer to insert the internal IR connection cable
24F
7
with the 3.5mm connector
that fits into the REMOTE IR opening on the rear panel. Connect the external
IR receiver to the REMOTE IR 3.5mm connector.
1 The first and the last units on the RS-485 line should be terminated (ON). Other units should be unterminated (OFF)
2 Covered by a cap. The 3.5mm connector at the end of the internal IR connection cable fits through this opening
3 Optional. Can be used instead of the front panel (built-in) IR receiver to remotely control the machine (only if the internal
IR connection cable has been installed)
4 Turn the machine OFF using the power switch and then turn it ON while pressing the ETH Factory Reset button. The unit
will power up and load its memory with the factory default definitions
5 Model: C-A35M/IRR-50
6 Model: C-A35M/A35F-50
7 P/N: 505-70434010-S

   Find Your Products By Category