Panasonic Car Video System LCD Video Monitor User Manual

0

Out of 0 Ratings

Owner's of the Panasonic Car Video System LCD Video Monitor gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 80
 
42
Main Menu (continued)
43
PIXEL TO PIXEL and PIXEL POSITION
The PIXEL TO PIXEL function allows you to check images at their actual pixel resolution. (HD signals only)
Press the <FUNCTION1> to <FUNCTION5> (→page 12) button to which the [PIXEL TO PIXEL] function has been assigned to turn
the function on. Then press the <FUNCTION1> to <FUNCTION5> (→page 12) button to which the [PIXEL POSITION] function has
been assigned to position the display of signals. Each press of the button will change the display position of the signal.
Underlined values indicate factory defaults.
Item Setting Description
PIXEL TO PIXEL
*
13
*
14
OFF
ON
Sets whether to display the screen display size at the input signal size.
[OFF] Not displayed [ON] Displayed.
Compatible formats
• Only available in the left screen when a PICTURE ASSIST function is on
1080/60i, 1080/59.94i, 1080/50i, 1080/60p, 1080/59.94p, 1080/50p, 1080/30p,
1080/29.97p, 1080/25p, 1080/24p, 1080/23.98p, 1080/25PsF, 1080/24PsF,
1080/23.98PsF
• Only available in the left screen and in 1-screen display when a PICTURE ASSIST
function is on
720/60p, 720/59.94p, 720/50p
PIXEL POSITION
LEFT
CENTER
RIGHT
Positions the display of signals [PIXEL TO PIXEL] is [ON].
[LEFT] Left of screen
[CENTER] Center of screen
[RIGHT] Right of screen
• Normally, when the input signal is 720/60p, 720/59.94p or 720/50p in the single screen
mode, the number of pixels of the monitor panel is greater than the number of samples
of the input signal. Although the image can be set, it will be displayed at CENTER
(screen center) and cannot be displayed at any other position.
*
13
The following settings are disabled when [PIXEL TO PIXEL] is ON.
• Setting [ANAMO] to [ON], and setting [SCAN] to [UNDER] in [VIDEO CONFIG]
• Any [HV DELAY] setting in [FUNCTION]
• [MARKER] display
*
14
Enabled during [SDI1], [SDI2], [HDMI], [YP
B
P
R
] and [DVI-VIDEO] input.
PIXEL POSITION display position sequence
PIXEL POSITION: → → → .....
LEFT CENTER RIGHT
CROSS HATCH
The CROSS HATCH function displays markers at regular vertical and horizontal intervals to facilitate composition and other tasks.
The marker line width is 1 dot per line and the interval is 120 dots/120 lines or 60 dots/60 lines depending on the [SIZE] setting in
the [MARKER] menu (→page 24).
Each press of the <FUNCTION1> to <FUNCTION5> (→page 12) button to which the CROSS HATCH has been assigned changes
the display.
Each press of the <FUNCTION> button to which the CROSS HATCH function is assigned changes the display as shown.
Press the same button again (to return to the original image without cross hatch)
HD/SD (16:9) mode
SD (4:3) mode
Press the
same button
again
Press the
same button
again
Dim cross hatch
Bright cross hatch

   Find Your Products By Category