Sharp Flat Panel Television Sharp Aquos LED-LCD TV User Manual

0

Out of 0 Ratings

Owner's of the Sharp Flat Panel Television Sharp Aquos LED-LCD TV gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 66
 
7
• In the installation procedure, be careful not to catch your fi ngers between the
TV set and the fl oor.
• Do not remove the stand from the TV unless using an optional wall
mount bracket to mount it.
• After attaching the stand to the TV, do not hold the stand when you
put up, set up, move or lay down the TV.
QUICK REFERENCE
■
LC-70LE657U/LC-60LE657U/LC-70LE655U/
LC-60LE655U/LC-70LE650U/LC-60LE650U/
LC-70C6500U/LC-60C6500U
1
Confirm that there are 12 screws (8 long screws
and 4 short screws) supplied with the stand unit.
2
1
Set the post for the stand unit onto the
polystyrene foam.
2
Attach the base to the post.
3
Insert and tighten the 8 screws into the 8
holes on the bottom of the base.
• Hold the stand unit securely with one hand,
and then tighten the screws.
■
LC-70LE657U/LC-70LE655U/LC-70LE650U/
LC-70C6500U
Long screws
FRONT
2
1
1
3
■
LC-60LE657U/LC-60LE655U/LC-60LE650U/
LC-60C6500U
Long screws
2
1
1
3
FRONT
3
1
Insert the stand into the openings on the
bottom of the TV.
• Make sure that the stand is fi rmly inserted into
the TV. Improper installation may result in tilting
of the TV set.
2
Insert and tighten the 4 screws into the 4
holes on the rear of the TV.
1
2
2
1
Short screws
Soft cushion
Attaching the Stand (for the 90/80 Inch Models)
Building the Work Table
Before attaching the stand to the TV, build a work
table on which to rest the TV.
• To build the table, use the cushioning materials
used in the packaging.
• Of the cushioning materials used, TOP-C is also
used during stand unit assembly. Be sure to
assemble the stand unit before building the work
table.
FRONT
TOP-L
TOP-R
TOP-C
1
Insert each of the cushioning materials in the
respective directions shown in the fi gure.
• Insert TOP-L and TOP-R into the left and right
sides of the case respectively.
• Insert TOP-C to fi t between the lines on the other
side of the case.
TOP-L
CASE
LINE
TOP-R
TOP-C
2
The case is equipped with push-in tabs to
hold the cushioning materials in place. Push
in the tabs (2 for each location) to secure the
cushioning materials in the case.
Push-in tabs
■
LC-90LE657U
Attach the joints and close the case.
1
Insert a joint into the hole on the side of the case.
2
Pressing the tab, fi x the joint into place.
1
2
TOP-L
TOP-R
JOINT
CASE
LINE
TOP-C
3
After you have built the work table, spread a
blanket or similar soft cloth over the table and
then lay the TV display down on the covered
table before attaching the stand to the TV.
• Do not use a small table for this.
• Refer to the operation manual for information on
attaching the stand.

   Find Your Products By Category