Crown Car Amplifier XTI2 SERIES User Manual

0

Out of 0 Ratings

Owner's of the Crown Car Amplifier XTI2 SERIES gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 52
 
XTi2 Series Power Amplifiers
page 5
Operation Manual
Get Started
Factory Preset #3: XOVER
Putting the amplifier in XOVER mode enables a 1.2kHz 4th order (24dB/octave)
filter that sends frequencies of 1.2kHz and below to Channel 1 output and
frequencies of 1.2kHz and above to Channel 2 output. The XTi2 Series amplifiers
come pre-loaded with a preset that makes it easy to configure the amplifier for
this operation.
Before you get started ensure that you:
1.
Connect signal source to Channel 1 ONLY using an XLR connector (the
amplifier inputs will automatically be put into Y mode when selecting this
preset).
2.
Connector the speaker as shown.
a.
Connect the speaker you wish to receive the low and mid frequencies (1.2kHz and below) to Channel 1 output
using Speakon
®
, Banana Plugs, or bare wire.
b.
Connect the speaker you wish to receive the high frequencies (1.2kHz and above) to Channel 2 output using Speakon
®
, Banana Plugs, or bare wire.
Follow these quick steps to configure the amplifier for XOVER operation:
1.
Push the “Set/Enter” button and you will see the word “Preset” flashing.
2.
Push the “Set/Enter” button again to enter the list of presets in the amplifier.
3.
Push the “Next/Down” or “PREV/UP” button until the screen displays “BIAMP”.
4.
Push the “Set/Enter” button to confirm your selection.
5.
The display will now read “BIAMP” with the Y icon and XOV icon highlighted.
LOW 1+/–
HIGH 2+/–
Factory Preset #4: BRG SUBS
Putting the amplifier in BRG SUBS (bridged subs) mode allows you to
bridge the amplifier for use with a single 8 or 4 ohm subwoofer. The inputs
are automatically summed, a 90Hz 4th order (24dB/octave) LowPass filter
is enabled, and the output mode is put into bridge-mono mode. The XTi2
Series amplifiers come pre-loaded with a preset that makes it easy to
configure the amplifier for this operation.
Before you get started ensure that you:
1.
Connect signal source to Channel 1 and Channel 2 using XLR
connectors (the amplifier inputs will automatically be summed together
when selecting this preset).
2.
Connector the speaker as shown.
a.
If using the binding post outputs, connect the positive terminal of the
speaker to the positive terminal of Channel 1 and the negative terminal of the speaker to the positive terminal of Channel 2.
b.
If using a Speakon
®
connector, connect the positive terminal of the speaker to 1+ and the negative terminal to 2+. Plug the connector into the Channel 1 output only.
Follow these quick steps to configure the amplifier for XOVER operation:
1.
Push the “Set/Enter” button and you will see the word “Preset” flashing.
2.
Push the “Set/Enter” button again to enter the list of presets in the amplifier.
3.
Push the “Next/Down” or “PREV/UP” button until the screen displays “XOVER”.
4.
Push the “Set/Enter” button to confirm your selection.
5.
The display will now read “XOVER” with the Y icon and XOV icon highlighted.

   Find Your Products By Category