Panasonic Blu-ray Player Owners Manual Blu-ray DiscTM Player User Manual

0

Out of 0 Ratings

Owner's of the Panasonic Blu-ray Player Owners Manual Blu-ray DiscTM Player gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 40
 
- 29 -
Reference
You have forgotten your ratings password.
You want to cancel the ratings level.
¾ The ratings level returns to the factory
defaults.
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
– POWER LED starts to flash, and “00 RET”
is displayed on the screen.
3
Press
[1]
(right) repeatedly
on the remote
control
until “
03 VL
” is displayed on the screen.
4 Press [OK].
The TV screen turns black.
¾ In the following cases, HDMI authentication
takes place and a black screen is displayed:
–
[BDT270] When “24p(4K)/24p Output” is set to
“24p(4K)” or “24p”.
–
[BD93] When “24p Output” is set to “On”.
–
[BDT270] When the display is switched
between 2D and 3D images.
This unit does not recognize the USB
connection correctly.
¾ Disconnect and re-connect the USB cable. If
it still does not recognize the connection, turn
this unit off and on again.
¾ USB devices may not be recognized by this
unit when connected using the following :
– a USB hub
– a USB extension cable
¾ If you connect USB HDD to this unit, use the
USB cable that is supplied with the HDD.
The images from this unit do not appear on
the TV.
Picture is distorted.
¾ An incorrect resolution is selected in “HDMI
Resolution”. Reset the setting as follows:
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
– POWER LED starts to flash.
3 Press [8] and the blue button on the remote
control at the same time for more than
5 seconds.
Set the item again. (> 23)
– When Dolby Digital Plus, Dolby TrueHD,
and DTS-HD
®
audio are not output properly,
select “Yes” in “Restore Default Settings”
(> 27) and make proper settings.
¾
[BDT270] When “3D BD-Video Playback” in the
Setup menu is set to “Auto”, images may not
be output depending on the connection
method. After removing the disc from this unit,
select “Set before play” in the Setup menu,
and select “2D Playback” in the setup screen
displayed when playing 3D discs. (> 25)
¾
[BDT270] When outputting in 24p (4K), images
may be distorted depending on the HDMI
cable. Use an HDMI cable that supports 4K
output.
Video is not output in high-definition.
¾ Confirm that “HDMI Resolution” in the Setup
menu is set properly. (> 23)
[BDT270]
3D video is not output.
¾ Connect to a full high-definition TV.
¾ Is there a non-3D compatible amplifier/
receiver connected between this unit and a
TV? (> 10)
¾ Are the settings on this unit and the TV
correct? (> 17)
¾ Is the amplifier/receiver that is connected
between this unit and TV on?
¾ Depending on the connected TV, the video
being played back might switch to 2D video
due to changes in resolution etc. Check the
3D setting on the TV.
Picture

   Find Your Products By Category